SEADOO VTS TRIM RELAY FIX MANUAL

If you're installing an impeller on a Sea Doo, don't follow the manual when it calls for red loctite on the threads. If you've bought one of our carb kits, a great page by GroupK that details the procedures for carb fine tuning can be found HERE If you find an item on another site for less though let us know so we can fix that! Looking for a discount coupon? Our prices are already 10-20% less than everyone else so we don't play that game. YOU THEN CAN ENTER YOUR CC INFO WITHOUT HAVING TO SET UP A PAYPAL ACCOUNT. TO USE YOUR CREDIT CARD SELECT PAYPAL FOR YOUR PAYMENT METHOD THEN ONCE REDIRECTED THERE CLICK THE BUTTON THAT SAYS 'PAY WITH CREDIT/DEBIT CARD'. We accept Visa, Mastercard, Discover, and AmEx credit cards through PayPal WHAT YOU ENTER FOR SHIPPING IS WHERE IT'S GOING TO GO SO MAKE SURE THAT'S RIGHT BEFORE SUBMITTING YOUR PAYMENT! LATELY WE'VE HAD A BUNCH OF PEOPLE ENTERING THE WRONG SHIPPING ADDRESS INTO THE SITE WHEN ORDERING. ANY EMAIL INQUIRIES ALSO WILL BE ANSWERED TUESDAY THROUGH FRIDAY. ANY ORDERS PLACED OVER THE 3-DAY WEEKEND WILL BE PROCESSED AS SOON AS WE ARE OPEN TUESDAY. Make sure you pay attention when you wire the relays if you hear a buzz when you push your vts switch you screwed up on the wireing.NOTE WE ARE NOW IN OUR FALL SCHEDULE WHERE WE ARE CLOSED MONDAYS. If you wired it up correct everything will work just look at the gauge for trim position because with the relays the power will stay on as long as you have the button pushed. The relays can be put in a small watertight box and then just drill a hole for the wires to exit and seal them up. I bought the relays at radio shack part # 275-0001 for 6.95 each so after wire and connectors you will be in less then 20 bucks. When I did mine I ran new wires from the vts motor through the back of housing by drilling a hole and sealing it up with 5200

SEADOO VTS TRIM RELAY FIX PLUS

If the motor doesnвЂ™t turn remove the two screws on the motor and check the armature and brushes you might get lucky by cleaning them up and save a other-wise bad vts motor and add a-little grease to the shaft ends.ДЄfter you wire up the relays the trim gauge will work if it is any good.Д¬ut the green/white and the blue/ white wires from the vts 6 pin connector (switch side) but leave the other wires un-touched so you will have a vts gauge when you are done plus the vts switches will still have the original ground. Start by checking the vts motor disconnect both wires inside box and jumper wires negative to positive on battery and motor should rotateвЂ¦ Reverse the wires to check rotation the other direction. The black box is also radio shack at 2.99 and they have the rubber grommets in a bag for 2 bucks I have put on about 150 miles on the ski I put it on in the last month using it a-lot with no issues at all. No stop for the trim motor but if you are smart enough to look at the gauge you will have no problems.

I think the Seadoo trim a waste of time but some people like it so here is what I came up with and it works like a charm.

I buy ski's to re-sell and most have bad trims so this is what I came up with.

VTS Housings fail continuously and are costly to replace. Genuine OEM 1996 Seadoo XP GSX GTX 787 800 jetski relay module 278000656. (Compatible with Sea-Doo SeaDoo) Venom Brand VTS Trim & Start/Stop Switch Cover Button Set Fits Many 1996-2004 GSI GSX RX SP SPX XP/DI RFI LE. Just thought I would pass this on to help a few people fix there trim on the cheep. This is an aftermarket control module that replaces the internal VTS housing trim module and electronics that control the crafts trim function. Sea-Doo Personal Watercraft, 2002-11 Repair Manual All 4-Stroke Models (Seloc Marine Manuals) 49.85.

2022.03

Seadoo vts trim relay fix